Chatsworth GlobalFrame Cabinet - 48"(D), 24"(W) - No Side Panels

Features:

• Sturdy welded and bolted steel construction
• 3000 lb (1360 kg) equipment load capacity
• Adjustable depth mounting rails with marked and numbered U spaces
• Front and rear support for 19”EIA rack-mount equipment
• Perforated doors for front-to-rear airflow
• Four large cable knockouts on the top panel, one per corner
• Locking doors for physical security
• The top panel, doors and equipment mounting rails are electrically bonded to the frame
• Easy movement on included casters
• Easy access to leveling feet

Doors/Latches:

• Front door is curved, perforated metal
• Rear door is flat, perforated metal
• Swing handle latch with keyed lock
• Easy to remove; reversible to open from the right or left

Side Panels:

• None

Top Panel:

• Standard top panel
• Tool-less installation and removal (after removing shipping fasteners), spring-release pins secure the panel on the cabinet frame
• Includes 2.8”(71 mm) round cable ports in each corner with included rubber grommets to seal openings and four additional 2.8” (71 mm) knockouts (one in each corner). Additional rubber grommets are sold separately as accessories.
• The 2.8” (71 mm) round access ports can be removed entirely by removing the larger 4.5”W x 9.0”D (114 mm x 228 mm) rectangular knockouts.
• Includes holes to attach 12”W (300 mm) Cable Runway in parallel (side-to-side) orientation at the front or rear of the cabinet using the Cable Runway Elevation Kit (P/N 10506-X1X- sold separately); the holes are covered with plugs

Equipment Support:

• Two pairs of equipment mounting rails in the cabinet
• Adjustable depth, rails slide front-to-rear; marks on frame for easy alignment
• 1.75”H (44.45 mm) U spacing, marked and numbered bottom-to-top on all rails
• 19”W, Universal 5/8 inch – 5/8 inch – 1/2 inch (15.9 mm – 15.9 mm – 12.7 mm) vertical hole spacing complies with EIA/ECA-310-E
• Square punched holes that accept cage nuts
• Includes 25 each M6 cage nuts and screws
• Includes attachment points for accessory snap on Cable Ring Kits, order separately

Grounding/Bonding:

• Mounting rails, top panel and doors are electrically bonded to the cabinet frame
• A mounting location for a ground lug is provided on the cabinet frame

PDU Brackets:

• One pair of L-shaped brackets and installation hardware
• Attaches to the frame corner posts, 4.3” (109 mm) wide, requires a minimum 3.9” (99 mm) equipment mounting rail setback
• Use with CPI vertical PDUs or Power Strips for cabinets that are 68.5”H (1740 mm) or 70.5”H (1791 mm) with tool-less attachment points located 64.75” (1645 mm) apart
• Supports two 2.0”W (51 mm) or narrower PDUs side-by-side or one 4.5”W (114 mm) PDU

Chatsworth GF-1A400 Specifications:

Dimension Notes:
^1. Doors add approximately 1.0” (25 mm) to the frame depth of the cabinet. The front door is 2.2”D (56 mm) and adds approximately 1” (25 mm) to the frame depth. The rear door is approximately 1.0”D (25 mm) and does not add to the frame depth. See note 2.
^2. Depth at the base of the cabinet frame is 2.5” (64 mm) more than depth at the frame uprights. There is a 1.25” (32 mm) threshold on the front and rear of the cabinet that provides easy access to leveling feet. When installed, the front and rear doors cover this threshold. Frame uprights (corner posts) are approximately 2.9” (74 mm) deep.
^3. When adjusted to maximum depth, mounting rails wrap around the frame uprights (corner posts). Note: Cable Ring Kits cannot be attached to the rails when they are set to maximum depth.

GF-1A400 Accessories