ServerTech Sentry Rack PDU, Switched, 0U (CW-24V2-L30M)

This Server Technology product has been discontinued. For alternative product suggestions, please call your Server Racks Online representative at 1-866-722-5776.



The Server Tech CW-24V2-L30M is the Switched Cabinet PDU 24V which combines remote configuration and management with power distribution, power monitoring and environmental monitoring. Reboot a single or dual-power server with one command. Receive SNMP alerts when power or environmental conditions exceed thresholds. Assign users specific access rights to designated outlets or groups.

Only our Switched Cabinet PDU products provide the flexibility needed for all data centers and remote sites; including support for 20-amp or 30-amp power input, 208-240V or European 230V configuration; UL 60950-1 branch circuit protection; EN 60950-1:2001; SSL & SSH security; and SNMP-based input current monitoring. For cabinets with high-density servers, this cabinet distribution unit delivers unparalleled remote management solutions.

ServerTech Sentry Rack PDU, Switched, 0U (CW-24V2-L30M) - Click to enlarge

Server Technology
Please call 1-866-722-5776 to order

Server Tech CW-24V2-L30M Switched PDU Features:

  • Easy to use and access, secure, integral HTML Web GUI over HTTP/S, plus LDAP/S and TACACS+ external authentication and authorization support
  • Secure remote power management; reboot individual or grouped outlets (SSL, SSH, Telnet, SNMP, RS-232)
  • Outlets may be linked to one or multiple groups without loss of control of that individual outlet
  • Native power-up sequencing prevents in-rush current overload during initial start-up or after power loss. Unlike other products on the market, sequencing occurs during initial startup, after power loss and after user-initiated power cycling to prevent overload
  • True RMS input current monitor(s) on easy-to-read local LED, via network or serial connection
  • Optional temperature and humidity probes with 10-ft cords to allow sensors to be located in different locations
  • SNMP traps provide automated alerts for power and environmental conditions. Additionally, event notification is available via Syslog and email
  • Expandability: add additional outlets under one IP address through link unit
  • Local and remote notification if a branch circuit is down (FE will display on LED and through the web-based interface, SNMP and email alerts)
  • 3 Phase products have a separate LED for each phase to simplify load balancing

*Note: Additional product specifications are below.

Server Tech CW-24V2-L30M Specifications:

Mechanical  
Height 69 in. (1752 mm.)
Width 1.75 in. (44.5 mm.)
Depth 2.25 in. (57.2 mm.)
Input  
Available Input Voltages 208-240V 50/60Hz
Available Input Cord NEMA L6-30P Cord Set
Output  
Outlets (24) IEC 60320/C13
Amperage 30A
Branch Circuit Protection Compliant to UL 60950-1
Communications

10/100 BaseT Ethernet
HTTP/HTTPS
SSLv3/TLSv1
SNMPv2
SSHv2
Telnet
LDAPv3/LDAPS
TACACS+
RADIUS
RS-232 (Serial)
Standards

cTUVus – UL 60950-1-2003
CAN/CSA 22.2 No. 60950-1:2003
TUVGS – EN 60950-1:2001
FCC Class A, Part 15
CE
EMC-EN 55022 Class A, EN 55024


Question: I'm trying to log into one so that I can turn on all the power outlets. It seems that they are all powered off. I'm using hyper terminal plugged into the serial port. What am I missing?
Answer: Thank you for your inquiry. Unfortunately, detailed product support is beyond the scope of this simple FAQ. That being said, here a few thoughts. Once attached to the serial port and after pressing enter, you should see Sentry Version x.xx (where x.xx is the firmware version) followed by a user name prompt. To continue, a valid user name and password are required. If this information failed to display, check to see if a cross over cable is being used and the terminal is configured to support ANSI or VT100 at a supported data rate (300, 1200, 2400, 4800, 9600, 19200, 38400, 576000, or 11520 BPS) - 8 data bits-no parity-one stop bit and Device Ready output signal (DTR or DSR). Additional configuration information, specific commands and the factory reset procedure (if required) can be found in the product manual. The PDF manual for firmware version 5.3 can be downloaded here: http://cdn1.servertech.com/assets/documents/documents/225/original.... Manuals for additional Firmware versions are located here: http://www.servertech.com/support/technical_library.... For additional product support, we would recommend contacting Server Technology Support directly at the following link: http://www.servertech.com/support.